• Functional 5-key waterproof keypad.

• Large 6-digit display, 60 mm high, with very efficient SMD LEDs (software adjustment of the brightness intensity), complete of 6 Leds for indication of active functions, visible from over 25 m, with viewing angle up to 120° and with power up to 750 mcd.

• IP68 stainless steel case complete of wall fixing bracket.

• Calibration, Set-Up parameters, configurable from keyboard or from PC with DINI TOOLS.

• Max. 10.000e or multirange 2 x 3000e @ 0,3 µV/d in CE-M approved version for legal for trade use.

• Max. 1.000.000 displayable divisions viewable with internal resolution up to 3.000.000 points.

• Up to 8 signal linearisation points with DINITOOLS.

• A/D 24 bit sigma-delta 4-channel conversion, max.200 conv./sec. with automatic selection.

• Connectable with up to 16 analogue load cells with 350 Ohm input resistance.

• Management of a weighing system with up to 4 cells with digital equalisation or management of up to 4 independent weighing systems.

• Power supply from 110-240 Vac.

• Available as Scale or as Repeater version.

• EC Type Approval (EN45501)

• OIML R76

• OIML R61 - MID

• RS232/C bidirectional port configurable for connection to printer, PC, or other external units.

• RS485 bidirectional port configurable for connection to PC, PLC, or other external units.

• PROFIBUS bidirectional port (DGT60PB3GD model).

• 2 MOSFET 150 mA 48 Vac / 150 mA 60 Vdc (NO) outputs, with configurable functions.

• 2 optoisolator photocouplers: 12÷24 Vdc, 5 mA min - 20 mA max, with configurable functions.

• 16-bit analogue output (DGT60AN3GD model) 4-20mA / 0-5Vdc / 0-10Vdc at choice; maximum applicable voltage: 350 Ohm; minimum applicable voltage resistance: 10 kohm.
  
  
  TAKE NOTE:
  All the cables must be installed and protected according to the standards for electrical equipment.

• Version with specific program for use of the indicator as a universal weight repeater or as a multi-scale repeater (MASTER) in combination with DFW/DGT/MCW.
  
  

• FUNCTIONING MODES:
  - Multi-scale repeater (MASTER):
  function which allows to repeat up to 32 independent scales, with the possibility of managing their functions, or displaying and printing the sum of the weighs of all the scales.
  - UNIVERSAL weight repeater:
  function which allows to repeat the weight of any scales, through the configuration of the input string.

DGT603GD: weight indicator / repeater for ATEX zones 

 
Dimensions in mm.

FUNCTIONS

THROUGH KEYBOARD: Zeroing; Semi automatic and presettable tare, print and/or data transmission; ON/Stand-by. SELECTABLE: High Resolution Weighing x 10; Net/Gross or lb/kg conversion; Weighs totalisation; Formulation; Approved transmission of the weight to PC/PLC (with Alibi memory ALMEM option); Counting; In/Out Truck weighing; Hold e Peak. EXTERNAL INPUT: Simulation of key pressure; Keyboard lock. MOSFET OUTPUT: Set Point Control on the weight, either positive (in loading) or negative (in unloading), or on the pieces (counting mode), with programmable enabling/disabling thresholds, as direct check or upon weight stability. SERIAL PORTS: On all models: Reading of the net, gross, and tare weights; Clearing; Semi automatic and presettable tare; Scale switch; Setting of outputs activation thresholds; Reading/Writing of Alibi Memory. DGT60BC3GD and DGT60AN3GD models: Reading of microvolts or ADC converter for all the channels; Message display; Printing; Setting of APW in counting mode; Simulation of key pressure; MODBUS serial protocol. THROUGH 16 bit ANALOGUE OUTPUT (DGT60AN3GD): Analogue output proportional to the net or gross weight, either positive (in loading) or negative (in unloading).